Version History
Here you can find the changelog of Brain | iKon | Xbar | TracX since it was posted on our website on 2016-11-06.
The latest version is and it was updated on soft112.com on 19 April, 2024.
See below the changes in each version:
version N/A
posted on 2023-12-15
• Added to the Micro Brain2 FCU the management of the B-Aux3 channel on the CH4 connector to be able to control buzzer activation, retractable landing gear, lights, winch, smoke, etc. etc. via PWM signal
• Added handling of the new SKY telemetry parameter introduced by Spektrum with the November 21 AirWare update
[MORE...]
version N/A
posted on 2023-10-20
• Added the telemetry decodify of OMP ESC
• Implemented Forward Programming Integration for those who have Spektrum telemetry receivers on their models but have switched to using transmitters with OpenTX / EdgeTX operating systems and Multi Module Radio frequency. An LUA app will be released later
• Corrected the calculation of vibration frequencies with some production batches
[MORE...]
version N/A
posted on 2023-09-06
• Crossfire channel reception up to 16CH (with ELRS and Packet Rate 333Hz Full)
• New Brain2Crossfire.zip version of Crossfire Integration package (Release Notes inside) that now other than TBS work also with ELRS External Module. Note: this version of the LUA app work only starting from this new firmware and for both TBS and ELRS external modules
[MORE]
version N/A
posted on 2023-07-05
• Crossfire reception improvements (sensor loss occurrence zeroed)
• Completely new Brain2TBScrossfire.zip version of the TBS Crossfire Integration package (Release Notes inside). Work only starting from this new firmware (does not work with ELRS because ELRS Telemetry is for now only unidirectional, unlike TBS telemetry, which is bidirectional)
• Added for TBS Crossfire & ELRS Crossfire protocol the telemetry transmission of a Variometer data (Altitude & Vertical Speed)
[MORE....]
version N/A
posted on 2023-05-16
• Improvements, changes, and corrections to previous version 3.4.103 as per user suggestions and reports (ESC telemetry with F.Bus protocol, ESC telemetry with SUMD protocol, etc.)
• Improved serial communication of SYS port (using Remote USB or Bluetooth dongle) when simultaneously using Integrations which in this case are faster
• Added in the “Servo Setup (Output)” panel of the Wizard a new icon for Cyclic servo’s 760us/560Hz
[MORE....]
version N/A
posted on 2023-03-10
• Improvements, changes, and corrections to previous version 3.4.100 as per user suggestions and reports
• Added the management of new Brain2/iKon2 batch
• Revised the routine of “Tail Motor RPM2” parameter to be able to record higher speed
• Added the checkbox for VARIO telemetry also in ADVANCED
• In Spektrum Integration added the checkbox for VARIO telemetry and the loggable parameters “Rel.Altitude” & “VSpeed”
[MORE...]
version N/A
posted on 2022-03-18
. Added to the 11 Jeti telemetry transmitted values selected in the “Parameter Setup” tab of DIAGNOSTIC, also the “Log Parameter 12” value “Global Vibrations”. If an ESC is selected in “Telemetry Input” of panel 12 of the Wizard, are also transmitted “ESC Battery Voltage”, “ESC Battery Current”, “ESC Battery Used”, “ESC Battery Ripple”, “ESC Power Output”, “ESC LS RPM”, “ESC Temperature 1 (°C & °F)” values. If Hobbywing or Jive Pro or YGE are selected also “ESC Temperature 2 (°C & °F)”[MORE]
version N/A
posted on 2021-08-04
. Now also the SRXL2 signal coming from the “Bind/Prog/SRXL2” port of Spektrum “base” receivers (EG: AR6610T, AR8020T) is recognized and used
. Improved the channel reception immunity when app’s are connected to the Flight Control Units and F.Port2 and F.Port (inverted and un-inverted) protocols are used
[MORE...]
version N/A
posted on 2021-06-18
. Introduced in the Telemetry section the new “Min V to go (cell num.)” parameter that (optionally) signals by swashplate movement of the elevator if at power on the battery pack is low (instructions in the related balloon)
. Added F.Port2 uninverted (selecting multiprotocol icon) and inverted decoding (selecting the new icon). Developed and tested with Archer R4 (FW: Archer-X_2.1.7) and with the R-XSR (FW: "RXSR_ACCESS_2.1.7") receivers. No special cable required
[MORE...]
version 3.3.039
posted on 2020-12-13
. Introduced the possibility to control Tandem Rotors models such as the Vario Chinook
. Added the possibility to log RPM also from a second electric motor (EG: model with tail motor or model with two motors like Velos)
. Added the possibility to read and record in the Flight Logs the value of a PWM signal output from an external device
[MORE...]
version 3.3.030
posted on 2020-07-30
. Added the ability to log FrSky RSSI reading from S.Bus channel n°16 (RSSI is always measured from channel 16, the receiver, if it is a model able to send RSSI, must be set to send RSSI value pushing bind button for 5 seconds. With this mode channel 16 cannot be used as a normal channel)
. Increased the MAX value of “Rx Frame Rate uS” to 1000 also if it is not graphically visible to be able to intercept the cause of a Throttle Fail Safe
[MORE]
version 3.3.027
posted on 2020-07-07
. Added the management for logging in real time or into Flight logs also the Spektrum AVIAN / FIRMA ESC telemetry data
. Added in the Spektrum Integration (only) the telemetry selection also for Spektrum AVIAN / FIRMA ESC
. Added a message if “Also Spektrum AVIAN / FIRMA ESC telemetry” is selected when SRXL2 is not selected
[MORE]
version 3.3.019
posted on 2020-05-07
. Added a fix for the OpenTX Integration of Servo Frame rates
. Increased the delta value that trigger the event “Throttle limit reached”
. Revised the firmware update process. Initial cancellation now don’t start if communication is not working
. Events: modified "Acceleration > = 16g" to "Deceleration > =16g"
. Events: modified "Resetted to Factory defaults" to "Reset to Factory defaults"
[MORE]
version 3.3.006
posted on 2020-03-06
. Corrected in OpenTX Integrations “Servo0 angle” displayed value
. Corrected in OpenTX Integrations “Blade Number” & “Blade Length” functions when “Flybarred” is selected
. Added a workaround fix for the OpenTX Bug that when Fail Safe is set to “No Output”, instead of sending no signal, send -115% signals to all channels and then set fail safe flag. From now on, out of range values so high are discarded
[More]
version 3.3.003
posted on 2020-01-22
. With Spektrum telemetry, on the transmitter “Telemetry” page of Voltage/RPM/Temperature the Temperature value displayed is the higher between Temp1 and Temp2
. With NEW SRXLv2 protocol, the automatic assignment of channel is executed also after a Bind process
. After an automatic assignment of channels, the Channel Assignments page in Advanced -> Common -> Receiver, is updated
[MORE...]
version 3.3.000
posted on 2019-12-27
. From now the Aux channel is separated in to two different channels, one (B-Aux1) dedicated to the Auto Leve / Rescue function and the other (B-Aux2) dedicated to the CH2 output. During the first update the new B-Aux2 channel is set equal to the actual B-Aux1 channel so for users there is any change from the actual configuration.
[More...]
version 3.2.060
posted on 2019-10-31
NOTE: In this update package the Windows, Android and iOS apps only work with the new Firmware. As a result, previous firmware versions are deactivated and can no longer be downloaded. If for any reasons you do not want to update the firmware of your units, you should therefore avoid updating the Windows app ("Cancel" when a software update is proposed) and avoid updating the Android and iOS apps (by deactivating the “auto update” function of the app).
version 3.2.054
posted on 2019-07-31
. Wizard: moved panel 9 “Unit Orientation” to panel 2, all other panels are scaled by one position
. Added further controls for the swashplate displayed as selected in panel 7 of the Wizard
. Added message “SWASHPLATE NOT SELECTED” in panel 8 of the Wizard if swashplate was not correctly done
. Now it is possible to log also values of Z-Acceleration, X-Acceleration and Y-Acceleration (in G units)
version 3.2.050
posted on 2019-06-06
- 3.2.050 (firmware 3.2.050) 05 June 2019
. Added in firmware routines for FrSky Integration management
. Added a new power graphic engine for Logs/Vibrations/Events (license payment)
. Added the new menu “Real time Logs”
. Added the new menu “Recorded Logs”
. Added the new menu “Vibrations” (Real time and recorded)
. Added the new menu “Events”
[More...]
version 3.1.027
posted on 2017-11-04
• Added telemetry for Kosmik, Jive Pro, Kolibri, Kontrol-X ESC's. Is needed a new firmware release for the ESC not yet released from Kontronik, and a cable with the 5 pole kontronik connector
• Added for OpenTX Transmitters and FrSky receivers with Smart Port the Brain2 telemetry transmission of ESC data's (is needed a special cable adapter)
[More]
version 3.0.000
posted on 2017-01-16
- 3.0.000 (Firmware 3.0.000),- Activated Jeti EX-Bus telemetry data transmission for the value selected in "DIAGNOSTIC" -> "Parameter settings" tab,- Revised the Jeti Integration releasing a new brain.bin file, with all the new parameters added in this release and some other improvements/changes and a fix for timers,- Added Futaba S.Bus2 for telemetry data transmission,- Added Spektrum SRXL decoding including telemetry data transmission,[MORE]
version 2.0.026
posted on 2016-09-12
- 2.0.0026 (Firmware 2.0.0026),- Now, if for some reason the unit is powered on with Auto Level and/or Recue active in the transmitter, this error is displayed by the swashplate rolling movements instead the usual up/down movements,- With the Jeti integration if governor speed values are greater than 3.276, wrong values are displayed in the transmitter. Fixed,- With CW and CCW icons, tail asymmetry is set to +5% or -5% instead of +50% or -50%. Fixed,- Some instructions corrected / completed
